Metal parts used for Die Casting Airplane Parts. When it comes to aircraft assembly parts, the most important considerations are safety, strength and reliability. The metal parts will sustain turbulence in the upper atmosphere, and they will experience inertial forces …
Continue reading
Kinetic Die Casting Compares Die Castings To Other Production Processes
Die casting – A manufacturing process in which molten metal is injected, under pressure, into a hardened steel die or also called mold. Dies are often water-cooled. Dies are then opened, and the die castings are ejected (many times thousands of parts each day, sometimes only a few hundred). Once the tooling is paid for, die casting is a very inexpensive aluminum part manufacturing process. We can make over 2000 die casting parts a day.
Compare Die Casting Process
Die Casting Part Prices
Forgings – Compared with forgings, die casting can be more complex in shape and have shapes not forgeable, can have thinner sections, be held to closer dimensions, and have coring not feasible in forging.
Plastic Injection moldings – Compared with plastic injection moldings, die casting are stronger, stiffer, more stable dimensionally, more heat resistant, and are far superior to plastics on a properties/ $ cost basis. They help prevent radio frequency and electromagnetic emissions. For chrome plating, die castings are much superior to plastics. Die castings have a high degree permanence under load compared to plastics, are completely resistant to ultra-violet rays, weathering, and stress-cracking in the presence of various reagents. Manufacturing cycles for producing die castings are much faster than for injection moldings.
Extrusions – Compared to extrusions, die casting can be produced faster and more net shape. Features and depressions on the sides, tops and bottoms can be created in one operation. There is less waste using die casting than extrusion. Holes can be cast in place to save additional machining cost.
Stampings – Compared with steel stampings, one die casting can often replace several parts. Die casting frequently require fewer assembly operations, can be held within closer dimensional limits, can have almost any desired variation in section thickness, involve less waste in scrap, and are producible in more complex shapes. Die castings can be made in many shapes not producible in stamped form.
Screw Machine Parts – Compared with screw machine products, die castings are produced more rapidly, involve much less waste in scrap, can be made into shapes that are difficult or impossible to produce from bar or tubular stock, and may require fewer operations.
Sand castings – Compared with sand castings, die castings require much less machining, can be made with thinner walls, can have all or nearly all holes cored to size, can be held within much closer dimensional limits, and are produced more rapidly in dies which make thousands of die castings without replacement. Die castings do not require new cores for each casting, are easily provided with inserts die cast in place, have smoother surfaces and involve much less labor cost per casting.
Permanent mold castings – Compared with permanent mold castings, die castings can be made to closer dimensional limits and with thinner sections and holes can be cored to near net shape. Die castings are produced at higher rates with less manual labor, have smoother surfaces, and usually cost less per die casting.
Die Castings Compared to other Manufacturing Processes
|
Kinetic Die Casting Company, Inc. 6918 Beck Avenue, North Hollywood, California USA 91605 E-mail sales@kineticdiecasting.com (818) 982-9200 California Die Castings – Die Casting Photos – Technical FAQ – Die Casting Prices – Kinetic Die Casting Company What is Die Casting ? – Why Use Die Casting – Kinetic Abilities – Die Casting Offshore ? – Sand casting prices and die castings – Die Casting Tooling – Kinetic Newsletter |
If you no longer wish to receive these emails, you may unsubscribe here.
Posted in Blogger, Die Casting Parts, Diecasting Process, newsletter
Tagged #diecasting, Manufacturing
Leave a comment
Kinetic Die Casting Company: Precision Aluminum Die Casting in Los Angeles, California
Kinetic Die Casting Company is a U.S.-based aluminum die casting manufacturer located in Los Angeles, California. With a strong focus on quality, speed, and American-made production, the company has built a reputation as a reliable supplier of precision aluminum die cast parts for a wide range of industries. By combining experienced craftsmanship with modern manufacturing processes, Kinetic Die Casting supports customers from early product development through full production.
Aluminum die casting is one of the most efficient methods for producing complex metal components in medium to high volumes. Kinetic Die Casting specializes in this process, producing parts with excellent dimensional accuracy, repeatability, and surface finish. Aluminum die casting allows intricate shapes, thin walls, ribs, bosses, and mounting features to be formed directly in the mold, reducing the need for secondary machining or assembly. This near net shape capability helps customers lower total manufacturing costs while maintaining high performance standards.
Los Angeles Die Casting Company
Located in Los Angeles, Kinetic Die Casting is strategically positioned to serve customers throughout California and across the United States. Domestic manufacturing enables faster communication, shorter lead times, and greater flexibility compared to offshore suppliers. The company is known for its ability to respond quickly to customer needs, including fast-turn production schedules and low-quantity orders. In many cases, parts can be produced and shipped within weeks of receiving a purchase order, making Kinetic Die Casting an ideal partner for time-sensitive projects.
California Die Casting Company
Die Casting Part Prices
Kinetic Die Casting Company works with customers as both a supplier and a manufacturing partner. The company often participates in design and product development discussions, offering input on part geometry, material selection, tooling design, and manufacturability. This collaborative approach helps customers improve part performance, extend tooling life, and avoid unnecessary production costs. Early involvement in the design process frequently results in more efficient tooling and smoother production runs.
The company serves a diverse range of industries, including industrial equipment, electronics, hardware, military and defense-related manufacturing, and commercial products. Kinetic Die Casting supports everything from prototype and low-volume production to long-term, repeat production programs. This flexibility allows customers to scale manufacturing as their product demand grows.
Quality is a central focus at Kinetic Die Casting. Aluminum parts are produced using controlled processes and inspected to meet customer specifications and engineering drawings. The company offers additional services such as trimming, impregnation to seal porosity, machining, surface treatments, and complete inspection. For customers requiring domestic sourcing, Kinetic Die Casting provides certification of U.S. manufacture with production shipments.
By maintaining production in the United States, Kinetic Die Casting helps customers avoid the risks associated with overseas sourcing, including long lead times, shipping delays, quality issues, and inventory challenges. Pricing is quoted in U.S. dollars, and customers benefit from predictable costs and straightforward communication.
Kinetic Die Casting Company continues to be a trusted aluminum die casting source in Los Angeles, California. Through a combination of technical expertise, responsive service, and commitment to American manufacturing, the company delivers dependable aluminum die cast solutions for customers nationwide.
|
Kinetic Die Casting Company, Inc. 6918 Beck Avenue, North Hollywood, California USA 91605 E-mail sales@kineticdiecasting.com (818) 982-9200 California Die Castings – Die Casting Photos – Technical FAQ – Die Casting Prices – Kinetic Die Casting Company What is Die Casting ? – Why Use Die Casting – Kinetic Abilities – Die Casting Offshore ? – Sand casting prices and die castings – Die Casting Tooling – Kinetic Newsletter |
If you no longer wish to receive these emails, you may unsubscribe here.
Why Draft Angle Is Important for Die Casting Manufacturers
A small die casting design detail requires attention for its outsized impact on quality, cost, and production efficiency: the draft angle in die casting parts.
Die casting draft angle refers to the slight taper applied to vertical surfaces of a die cast part, allowing it to be released cleanly from the steel die after solidification. While the concept has been standard practice for decades, industry experts say misunderstandings about draft angle continue to cause delays, redesigns, and unexpected tooling costs—particularly as demand rises for complex aluminum enclosures and precision components.
“Draft angle is not optional in die casting parts,” said one tooling engineer at a California aluminum die casting facility. “If the walls are straight with no taper, the part will stick in the die. That leads to damaged castings, excessive wear on tooling, and production downtime.”
Why Die Casting Part Draft Angle Matters
A380 Box
In aluminum die casting, molten metal is injected into hardened steel dies under high pressure. As the aluminum cools, it shrinks slightly and grips the die surfaces. Draft angle creates clearance, allowing ejector pins to push the part out smoothly without distortion.
Die Casting Industry guidelines typically recommend 1 to 2 degrees of draft per side, with two degrees considered a safe standard for most aluminum castings. However, the exact requirement can vary depending on wall thickness, surface finish, alloy selection, and whether slides or lifters are used in the tool.
Despite its importance, draft angle is often overlooked during early design stages, especially when parts are designed by engineers unfamiliar with die casting or adapted from machined or plastic components.
Die Casting Part Prices
Impact on Die Casting Part Dimensions
Draft angle directly affects part geometry. For box-shaped enclosures—common in electronics, automotive, and industrial applications—the internal and external dimensions change from top to bottom. A box that measures four inches wide at the opening may be significantly smaller at the bottom once draft is applied.
“If a customer designs a box to fit electronics tightly without accounting for draft, the components may not fit,” explained a die casting project manager. “That usually means redesigning the part or modifying the tool, both of which add time and cost.”
Cost and Quality Implications
From a business perspective, proper draft angle improves more than manufacturability. Adequate draft reduces tool maintenance, increases die life, improves surface finish, and stabilizes production rates. Conversely, insufficient draft can lead to scrap, flashing, or galling inside the die.
As manufacturers face tighter margins and shorter lead times, avoiding preventable tooling changes has become increasingly important.
A Growing Focus on Design for Manufacturing (DFM)
The renewed focus on draft angle reflects a broader industry trend toward die casting design for manufacturing (DFM). Many die casting companies now review customer designs early in the quoting process, flagging draft issues before tooling begins.
“With today’s complex parts and higher expectations, you can’t afford to treat draft as an afterthought,” said the engineer. “It has to be designed in from the start.”
As die casting continues to serve industries ranging from aerospace companies, electric vehicles to renewable energy, understanding fundamentals like draft angle in die casting parts remains essential. Sometimes, the smallest angles make the biggest difference.
|
Kinetic Die Casting Company, Inc. 6918 Beck Avenue, North Hollywood, California USA 91605 E-mail sales@kineticdiecasting.com (818) 982-9200 California Die Castings – Die Casting Photos – Technical FAQ – Die Casting Prices – Kinetic Die Casting Company What is Die Casting ? – Why Use Die Casting – Kinetic Abilities – Die Casting Offshore ? – Sand casting prices and die castings – Die Casting Tooling – Kinetic Newsletter |
If you no longer wish to receive these emails, you may unsubscribe here.
Competitor Special Offer 2026
Dear Die Casting Competitor – A380 Aluminum Die Casting Parts Shipped To Our Competitor In Two Weeks.
Kinetic Die Casting
All die casting companies get into situations where we cannot deliver aluminum die casting parts to our customers, as we promised. Usually, this is caused by equipment downtime or problematic, long running die casting jobs in production. One of my customers complained last year that a die casting company was requiring a 12 to 14 week lead-time.
Many of our die casting jobs are for less than 1,000 die casting parts in A380 aluminum. We are constantly changing out our 12×15 units using A380 Aluminum once or twice a week. Many of our die casting jobs require 500 die casting parts, or less.
Consider sending Kinetic Die Casting Company your 12×15 unit die tool and we will setup and ship to you your required quantity, up to 1,000 parts made in A380 aluminum, in usually less than two weeks. Also, send us your trim die, if available, and we will die trim your parts. Otherwise, we will break the gates or sand and deburr the parts. You will specify the details in your purchase order. We can ship more than 1,000 parts if needed or establish regular deliveries in smaller quantities.
Of course, we will setup and run larger quantities of 5,000 or more, complete die casting tooling, and/or other die casting alloys. These die casting part deliveries will take a little longer. Call us to discuss your needs.
With that shipment you will also receive a CofC (Certificate of Conformance) with metal certifications from our metal supplier and a Certificate of U.S. Manufacture.
Call us or email us anytime to discuss, Save this email for when you get too busy later this year.
Kinetic Die Casting Company, Inc.
818-982-9200 or sales@kineticdiecasting.com
ps. It is sad that this needs to be mentioned. We have worked with die casting competitors in the past. Kinetic Die Casting has never “poached” customers. We have never contacted your customers directly if you send us a die casting part job to run.
Posted in Competitors
Leave a comment
2026 Die Casting Tooling Transfer Special
Kinetic Die Casting Company has a special offer to our current die casting customers and our new die casting customers. Some of our customers buy castings from a different die casting source other than us. Sometimes there are problems with that that other die casting part source with die casting part quality or delivery of die casting parts of several weeks. It would be a great idea to send Kinetic Die Casting Company that die casting tooling for better quality of faster part deliveries, but it is a difficult decision to make. So many questions: How do you get die casting prices? Are the Kinetic Die Casting Company better quality parts more expensive? Is faster die casting parts delivery more costly? We have your answers.
Die Casting Tooling Transfer Special
.
Manufacturing companies that transfer their die casting tooling to Kinetic Die Casting Company with a purchase order for die casting parts will get better quality parts in typically less than four weeks. and we make your American made die casting parts in just a few weeks. What will these better quality parts delivered fast to you cost? The same price you paid your previous die casting parts supplier. We can make parts with any die complete casting tool or DME Unit Die Tool unless it is larger than our die casting machine will hold, over 24 inches wide. We can make parts in your tool, even if that tool was made Over Seas. We will make your American made die casting parts in our North Hollywood, California USA die casting company.
Kinetic Die Casting Company, a better die casting part supplier.
Kinetic Die Casting Company makes that tooling transfer decision easier.
1. Send us your die casting tooling (descriptions of die casting tooling and molds)
2. Send us a purchase order made to us with your old supplier’s prices.
3. We will honor the die casting part price paid to the old die casting part supplier.
4. You will get better die casting parts than you received before.
5. We will ship the die casting parts to you in less than 4 weeks.
“The Parts We Make Today, We Ship Today”
Kinetic Die Casting Company makes:
- American Aluminum Heat Sink Die Castings
- American Automotive Die Casting Parts
- American Airplane Die Casting Parts
- American Made Light Fixture Die Casting Parts
- American Consumer Products Aluminum Die Casting Parts
- American Made Aluminum Aerospace Die Casting Parts
- American Military Die Casting Parts
- Die Casting Tooling
Permalink: https://www.kineticdiecasting.com/kdc/2026-die-casting-tooling-transfer-special/
|
Kinetic Die Casting Company, Inc. 6918 Beck Avenue, North Hollywood, California USA 91605 E-mail sales@kineticdiecasting.com (818) 982-9200 California Die Castings – Die Casting Photos – Technical FAQ – Die Casting Prices – Kinetic Die Casting Company What is Die Casting ? – Why Use Die Casting – Kinetic Abilities – Die Casting Offshore ? – Sand casting prices and die castings – Die Casting Tooling – Kinetic Newsletter |
If you no longer wish to receive these emails, you may unsubscribe here.
Posted in Aircraft Parts, Aluminum Die Casting, Aluminum Heatsinks, Auto Parts, Blogger, Bracket, Business, Customers, Die Casting Parts, Employee, Enclosures, Golf, Handle, Kinetic Die Casting Company, Lighting, newsletter, Supplier, Tooling Die Casting
Tagged #diecasting, #DieCastingCompany, #kineticdc, Aluminum Auto Parts, die casting tooling, Heat Sinks, Manufacturing, Military Die Castings, Tooling Die Casting, Zinc Die Casting
Leave a comment
