August 25, 2017 – Join us for our annual NADCA Chapter 30 golf tournament. California’s two largest metal casting chapters are coming together once again for a day of golf and networking. Over 135 industry professionals and suppliers participated last …
Continue reading
Comparison of Die Casting Tooling Types
Die Casting Tooling Types – Kinetic Die Casting Company produces die casting tooling for may types of die casting products.
- Die Casting Inserts
- Die Casting Mold Bases
- Unit Die – Die Casting Tooling
- Complete Die Casting Tooling
- Die Casting Trim Die Tooling
Die Casting Inserts –
Typically the least expensive tool to buy to get die casting parts. The cost of an insert starts at about $6000 and could range upward to over $20,000. The inserts can weigh as little as 30 – 40 pounds or more than 100 pounds. And typically the die casting inserts are only 4″-6″ larger than the part that needs to be produced.
Die Casting Inserts need to be mounted into a Die Casting Mold Base. If the die casting part needs a slide or slides. The mold base could be more costly.
Die Casting Mold Bases –
The Die Casting Insert Tool is mounted into a mold base to make die casting parts. The mold base is very large (usually over 15 inches), heavy (usually over 1500 pounds) and expensive (usually over $4,000). The mold base is necessary to control the temperature and pressures in die casting. The mold base has a hole to allow the metal to be injected into the tool. The mold base has special clamping slots so it can be mounted into the die casting machine.
Unit Die – Die Casting Tools –
A special die casting tool that is used to reduce the cost from a complete die casting tool and more efficient than die casting insets is the unit die tool, sometimes called a DME unit die. The unit die tool is easier and faster to change out in a die casting machine. Sometimes as little as half an hour verses sometimes four hours as a complete tool, or six hours as a die casting insert. It requires that the die casting company have a master DME unit holder mounted in a die casting machine. The unit dies are universal in the die casting industry and can be moved from one die casting company to another easier, similar to complete tooling, than die casting inserts. Unit dies are produced in three sizes, depending on the size of the part to be produced. 10×12 (pronounced ten by twelve), 12×15 (pronounced twelve by 15), and 15×18 (pronounced fifteen by eighteen)
Complete Die Casting Tooling –
The best quality tool. The most expensive tool. The tool that is the easiest to move from one die casting company to another. This tool is the complete package, cavity inserts and mold base. It mounts directly into the die casting machine. It controls the temperature and pressure much better than it’s counterparts.
Die Casting Trim Dies –
A die casting trim die cuts the excess material around the die casting part (flash). The die casting trim die mounts in a hydraulic press and saves time and produces a better part than sanding parts.
See our Website:
http://www.kineticdiecasting.com/tooling.html
http://www.kineticdiecasting.com/tooling_die_casting.html
Whether, you need die casting parts produced in aluminum or in zinc, contact Kinetic Die Casting Company to purchase your parts or die casting tooling.
Posted in Tooling Die Casting
Tagged Die Cast Mold, die casting tooling, Mold Base, Molds, Tooling Die Casting, Tooling Inserts
1 Comment
The Part that Aluminum Plays
The Part that Aluminum Plays. Aluminum parts types are distinguishing because this exacting metal lends to its die cast parts the properties of being lightweight and yet hard, with high electric as well as thermal conductivity, high reflectivity when refined to a gloss, corrosion resistance, non combustibility, formability, and capacity to be recycled.
Due to the built-in properties of this metal, aluminum parts types are a desired in the airplane construction business, in the car manufacturing business, and in the bicycle manufacturing business– this due to its strength and light weight. Aluminum is also fabricated into large electrical conductors and cables, and computer manufacturers are now utilizing aluminum parts in the casing of their products– this again is due to another one of its properties, that of electric and thermal conductivity. Other aluminum parts varieties are found in numerous products such as cooking utensils, food and drink packaging, extrusions such as window frames and door frames, and mirror coatings for telescopes as well as the commonplace looking-glass.
Aluminum is a metal most plentiful on earth. Although this is so, it is popular as a recyclable product. Visit any recycling plant and you are sure to see some aluminum parts varieties. These might be aluminum cans from soda drinks, bits and parts other scraps. Some might be torn, re-melted, fashioned into blocks, and whatnot. All the aluminum scrap metal is effortlessly recycled merely by re-melting them and pouring the melted metal once again into a mold. Then the aluminum die casting procedure can begin again.
Kinetic Die Casting manufactures products like aluminum hardware, and aluminum boxes. If you would like more information on Kinetic Die Casting, please visit our website:Kinetic Die Casting Company
A380 Aluminum Alloy verses A413 Aluminum Alloy
The two more common types of die casting aluminum used by Kinetic die Casting Company are A380 aluminum and A413 aluminum. There are reasons to use either metal.
So here are a few of the details (http://www.kineticdiecasting.com/casting_aluminum.html):
A380
Availability – More
Material cost – Less
Flexibility – More
Thermal Conductivity – Less
Electrical Conductivity – More
Pounds/Inch – More
Pressure Tight – Less
Surface Polish – Less
A413
Availability – Less
Material cost – More
Flexibility – Less
Thermal Conductivity – More
Electrical Conductivity – More
Pounds/Inch – Less
Pressure Tight – More
Surface Polish – More
A380 is the most common die casting aluminum used worldwide. Most part blue prints do not call out the aluminum type so the default is A380.
Call Kinetic Die Casting Company at 818-982-9200 or send us an email with your questions at sales@kineticdc.com
There is a chart on this web page that give much more details:
Alloys for Aluminum Die Casting
Kinetic Die Casting is a california die casting companycalifornia die casting company that manufactures die cast parts. If you would like more information or request a quote, vist our website:Kinetic Die Casting Company
Posted in Diecasting Process, newsletter
Tagged aluminum, Aluminum Alloys, Aluminum Die Casting Alloy, Die Casting Alloys
3 Comments
Aluminum Part Types – All You Need to Know
Aluminum Part Types – All You Need to Know. Aluminum die casting requires a lot of tools and parts to make the ideal dies. The method has been well known to supply a simple method for numerous constructors to generate the most perfect components to different automobiles and the likes. Aluminum parts types are not that simple to distinguish particularly for a person who is quite new in the die casting process. Since the system also requires a series of melted metals from copper, lead and zinc, a lot of aluminum part types are desirable to come up with the best die that possesses the precise instructions by the customer. Cold chambered and hot chambered are just two of the aluminum parts types particularly utilized for the definite machine in die casting.
In most cases, die casters wish to apply all aluminum part types while die casting. This makes the procedure more experimental, and can sometimes create the best outputs at the end of the sessions. Nevertheless, there is a surprising difference between a cold chambered die casting machine from a hot chambered one. For example, a die caster cannot merely use hot chambered types when handling aluminum material. This type of material is well-matched to a die casting machine that is cold chambered. Molds for aluminum die casting may also have parts that do not require cavities. This type of mold significantly differs in price compared to those with cavities. A lot of the parts sold for aluminum die casting often come with considerable product descriptions to let you decide which of the aluminum part types you are about to obtain.
Kinetic Die Casting manufactures die casting metal parts creating products like roofing tile molds, lighting parts, and military parts. If you would like more information about Kinetic Die Casting, visit our website:Kinetic Die Casting Company
Die Casting Comparison of Zinc Parts and Aluminum Parts
Die Casting Comparison of Zinc Parts and Aluminum Parts. Kinetic Die Casting Company produces parts for our customers in two types of metals. Aluminum and Zinc alloys. Most of the parts we produce are in aluminum.
When we get a quote request that does not specify the materiel, we ask a few questions to determine which metal would be better for them.
- Does weight matter? Zinc weighs about two and half (2.44) times more than aluminum. In other words, a part that weighs five (5) pounds in aluminum will weigh over twelve (12.22) pounds in zinc.
- Do you need EMI/RF shielding? Do you need electrical conductivity? Aluminum is much more electrically conductive than zinc, making it a better shield for RF/EMI.
- Do you need thermal conductivity? Aluminum is used by many manufacturers as a heat sink.
- Do you want parts with a highly polished finished surface? Zinc polishes very well, much better than aluminum.
- Do you need your parts plated? Zinc parts can be plated much better than aluminum.
- Are you intending to use the parts in a salt environment? Aluminum decays faster than zinc in a salty environment.
See our blog:
https://www.kineticdiecasting.com/kdc/
Whether, you need die casting parts produced in aluminum or in zinc, contact Kinetic Die Casting Company to purchase your parts or die casting tooling.
Contact Kinetic Die Casting Company to buy
Links:
Kinetic Die Casting manufactures die cast parts for their customers. If you would like to know more about what is die casting or if you would like a quote, please visit our website:Kinetic Die Casting Company
Posted in Die Casting Parts
Tagged Aluminum Die Casting, Diecasting Process, Manufacturing, Zinc Die Casting
4 Comments
